AVBbShv, AVBbShvng, AVBbShvng-LS

TU U 27.3-38456790-015:2019
Power cables with plastic insulation
AVBbShv, AVBbShvng, AVBbShvng-LS

insulated power cable (flixibility Class 1 & 2) with polyvinylchloride plasticate belt insulation, BbShv type protective coating, polyvinylchloride plasticate protective hose
А Aluminium conductive core
V Polyvinylchloride plasticate insulation & sheath
Bv Steel tape armour
Sgv Polyvinylchloride plasticate protective hose
ng Non-combustible
ng-LS Non-combustible, reduced smoke and gas release

Operating and installation requirements

  • Ambient temperature from -50°C to 50°C.
  • Relative humidity up to 98% at temperatures up to 35°C.
  • Cables can be laid without preheating at temperatures not lower than –15°C.
  • Minimum bending radius during installation should be not less than 10 outer diameters of a single core cable and 7.5 outer diameters of a multi-core cable.
  • Long-term temperature rise limits for cable cores should not exceed 70°C.
  • Temperature limit in the overload mode is max 90°C.
  • Rated alternating voltage up to 0.66 kV and up to 1kV.
  • Warranty service life is 5 years.
  • Service life is minimum 30 years.

Wires intended use
AVBbShv, AVBbShvng, AVBbShvng-LS

Cables are intended for transmission and distribution of electric power in permanent equipment for 0.66 kV and 1 kV nominal AC voltage and 50 Hz frequency

Used for laying in the ground (in trenches), premises, tunnels, channels, partially flooded structures subject to various corrosive factors, as well as in the open air, if not exposed to significant tensile forces, but in the presence of mechanical damage risk during operation.

Conductor design
AVBbShv, AVBbShvng, AVBbShvng-LS

Core count Rated voltage, kV
0,66/1
Main cores nominal cross-section, mm2
1 - 16 - 240
2, 3, 4, 5 4 - 6 16 - 240

Design data for
AVBbShv, AVBbShvng, AVBbShvng-LSwires

Core nominal cross-section, mm2 Nominal thickness, mm Nominal cable diameter, mm Maximum cord resistance at 20°C, Ohm/km Minimum value of insulation resistance at 20°C, MOhm/km Calculated mass of 1 km cable, kg
insulation sheath АVbBshv
1х16 0,9 1,4 13,6 1,91 5,8 331
1х25 1,2 1,4 15,6 1,20 5,6 423
1х35 1,2 1,5 16,8 0,868 4,9 485
1х50 1,4 1,5 18,6 0,641 4,8 588
1х70 1,4 1,6 20,6 0,443 4,1 678
1х95 1,6 1,7 23,0 0,320 4,1 829
1х120 1,6 1,7 24,6 0,253 3,7 939
1х150 1,8 1,8 26,8 0,206 3,7 1134
1х185 2,0 1,9 29,2 0,164 3,7 1329
1х240 2,0 2,0 32,1 0,125 3,6 1614
2х4 0,7 1,4 12,7 7,41 10,1 352
2х6 0,7 1,4 13,8 5,11 8,7 394
2х10 0,9 1,5 17,4 3,08 7,1 463
2х16 0,9 1,6 19,6 1,91 5,8 599
3х4 0,7 1,4 13,3 7,41 10,1 393
3х6 0,7 1,4 14,5 5,11 8,7 445
3х10 0,9 1,5 18,3 3,08 7,1 523
3х16 0,9 1,6 20,7 1,91 5,8 701
3х25 1,2 1,8 25,1 1,20 5,6 954
3х35 1,2 1,8 27,6 0,868 4,9 1122
3х50 1,4 2,0 31,6 0,641 4,8 1440
3х70 1,4 2,1 35,7 0,443 4,1 1703
3х95 1,6 2,3 42,3 0,320 4,1 2149
3х120 1,6 2,4 45,7 0,253 3,7 2485
3х150 1,8 2,6 50,3 0,206 3,7 3005
3х185 2,0 2,8 55,6 0,164 3,7 3593
3х240 2,0 2,9 61,0 0,125 3,6 4462
4х4 0,7 1,4 14,3 7,41 10,1 446
4х6 0,7 1,4 15,6 5,11 8,7 510
4х10 0,9 1,6 19,9 3,08 7,1 617
4х16 0,9 1,7 22,6 1,91 5,8 846
4х25 1,2 1,8 27,5 1,20 5,6 1130
4х35 1,2 1,9 30,3 0,868 4,9 1357
4х50 1,4 2,1 34,8 0,641 4,8 1792
4х70 1,4 2,2 39,4 0,443 4,1 2087
4х95 1,6 2,5 46,6 0,320 4,1 2696
4х120 1,6 2,6 50,5 0,253 3,7 3126
4х150 1,8 2,8 55,6 0,206 3,7 3730
4х185 2,0 2,9 61,5 0,164 3,7 4539
4х240 2,0 3,1 67,5 0,125 3,6 5583
5х4 0,7 1,4 15,4 7,41 10,1 512
5х6 0,7 1,5 16,9 5,11 8,7 592
5х10 0,9 1,6 21,8 3,08 7,1 722
5х16 0,9 1,7 24,8 1,91 5,8 1018
5х25 1,2 1,9 30,2 1,20 5,6 1373
5х35 1,2 2,0 33,3 0,868 4,9 1674
5х50 1,4 2,2 38,4 0,641 4,8 2180
5х70 1,4 2,4 44,8 0,443 4,1 2576
5х95 1,6 2,6 51,5 0,320 4,1 3343
5х120 1,6 2,8 55,8 0,253 3,7 3890
5х150 1,8 2,9 61,6 0,206 3,7 4720
5х185 2,0 3,2 68,2 0,164 3,7 5849
5х240 2,2 3,4 76,2 0,125 3,6 7209

Note: Calculated and nominal data can deviate from the actual data.
Identification markings meet fire safety requirements under DSTU 4809:2007
AVBbShv – PB 100000000
AVBbShvng – PB 120000000
AVBbShvng-LS – PB 123111000